Configuring Logging with CLI

This section provides information to configure logging using the command line interface.

Topics in this section include:

  1. Log Configuration Overview on page 485
    1. Log Types on page 485
  2. Basic Event Log Configuration on page 486
  3. Common Configuration Tasks on page 487
  4. Log Management Tasks on page 497

Log Configuration Overview

Configure logging parameters to save information in a log file or direct the messages to other devices. Logging does the following:

  1. Provides you with logging information for monitoring and troubleshooting.
  2. Allows you to select the types of logging information to be recorded.
  3. Allows you to assign a severity to the log messages.
  4. Allows you to select the source and target of logging information.

Log Types

Logs can be configured in the following contexts:

  1. Log file — Log files can contain log event message streams or accounting/billing information. Log file IDs are used to direct events, alarms/traps and debug information to their respective targets.
  2. SNMP trap groups — SNMP trap groups contain an IP address and community names which identify targets to send traps following specified events.
  3. Syslog — Information can be sent to a syslog host that is capable of receiving selected syslog messages from a network element.
  4. Event control — Configures a particular event or all events associated with an application to be generated or suppressed.
  5. Event filters — An event filter defines whether to forward or drop an event or trap based on match criteria.
  6. Accounting policies — An accounting policy defines the accounting records that will be created. Accounting policies can be applied to one or more service access points (SAPs).
  7. Event logs — An event log defines the types of events to be delivered to its associated destination.
  8. Event throttling rate — Defines the rate of throttling events.

Basic Event Log Configuration

The most basic log configuration must have the following:

  1. Log ID or accounting policy ID
  2. A log source
  3. A log destination

The following displays a log configuration example for the 7750 SR.

A:ALA-12>config>log# info
#------------------------------------------
echo "Log Configuration "
#------------------------------------------
        event-control "bgp" 2001 generate critical
        file-id 1
            description "This is a test file-id."
            location cf1:
        exit
        file-id 2
            description "This is a test log."
            location cf1:
        exit
        snmp-trap-group 7
            trap-target 11.22.33.44 "snmpv2c" notify-community "public"
        exit
        log-id 2
            from main
            to file 2
        exit
----------------------------------------------
A:ALA-12>config>log#

Common Configuration Tasks

The following sections describe basic system tasks that must be performed.

  1. Configuring a File ID on page 488
  2. Configuring an Event Log on page 487
  3. Configuring an Accounting Policy on page 488
  4. Configuring Event Control on page 489
  5. Configuring a Log Filter on page 490
  6. Configuring an SNMP Trap Group on page 490
  7. Configuring a Syslog Target on page 496

Configuring an Event Log

A event log file contains information used to direct events, alarms, traps, and debug information to their respective destinations. One or more event sources can be specified. File IDs, SNMP trap groups, or syslog IDs must be configured before they can be applied to an event log ID.

Use the following CLI syntax to configure a log file:

CLI Syntax:
config>log
log-id log-id
description description-string
filter filter-id
from {[main] [security] [change] [debug-trace]}
to console
to file file-id
to memory [size]
to session
to snmp [size]
to syslog syslog-id}
time-format {local|utc}
no shutdown

The following displays a log file configuration example:

ALA-12>config>log>log-id# info
----------------------------------------------
...
log-id 2
            description "This is a test log file."
            filter 1
            from main security
            to file 1
exit
...
----------------------------------------------
ALA-12>config>log>log-id#

Configuring a File ID

To create a log file a file ID is defined, specifies the target CF drive, and the rollover and retention interval period for the file. The rollover interval is defined in minutes and determines how long a file will be used before it is closed and a new log file is created. The retention interval determines how long the file will be stored on the CF before it is deleted.

When creating new log files in a compact flash disk card, the minimum amount of free space is the MINIMUM of 10% of Compact Flash disk capacity OR 5Mb (5,242,880 = 5 * 1024 * 1024).

The following displays a log file configuration example:

A:ALA-12>config>log# info
------------------------------------------
        file-id 1
            description "This is a log file."
            location cf1:
            rollover 600 retention 24
        exit
----------------------------------------------
A:ALA-12>config>log#

Configuring an Accounting Policy

Before an accounting policy can be created a target log file must be created to collect the accounting records. The files are stored in system memory of compact flash (cf1: or cf2:) in a compressed (tar) XML format and can be retrieved using FTP or SCP. See Configuring an Event Log on page 487 and Configuring a File ID on page 488.

Accounting policies must be configured in the config>log context before they can be applied to a service SAP or service interface, or applied to a network port.

The default accounting policy statement cannot be applied to LDP nor RSVP statistics collection records.

An accounting policy must define a record type and collection interval. Only one record type can be configured per accounting policy.

When creating accounting policies, one service accounting policy and one network accounting policy can be defined as default. If statistics collection is enabled on a SAP or network port and no accounting policy is applied, then the respective default policy is used. If no default policy is defined, then no statistics are collected unless a specifically defined accounting policy is applied.

By default, the subscriber host volume accounting data are based on the 14-byte Ethernet DLC header, 4-byte or 8-byte VLAN Tag (optional), 20-byte IP header, IP payload, and the 4-byte CRC (everything except the preamble and inter-frame gap). See Figure 17. This default can be altered by the packet-byte-offset configuration option.

Figure 17:  Subscriber Host Volume Accounting Data 

The following displays an accounting policy configuration example:

A:ALA-12>config>log# info
----------------------------------------------
accounting-policy 4
description "This is the default accounting policy."
record complete-service-ingress-egress
default
to file 1
exit
accounting-policy 5
description "This is a test accounting policy."
record service-ingress-packets
to file 3
exit

Configuring Event Control

The following displays an example of an event control configuration:

A:ALA-12>config>log# info
#------------------------------------------
echo "Log Configuration"
#------------------------------------------
        throttle-rate 500 interval 10
        event-control "oam" 2001 generate throttle
        event-control "ospf" 2001 suppress
        event-control "ospf" 2003 generate cleared
        event-control "ospf" 2014 generate critical
..
----------------------------------------------
A:ALA-12>config>log>filter#

Configuring a Log Filter

The following displays a log filter configuration example:

A:ALA-12>config>log# info
#------------------------------------------
echo "Log Configuration "
#------------------------------------------
        file-id 1
            description "This is our log file."
            location cf1:
            rollover 600 retention 24
        exit
        filter 1
            default-action drop
            description "This is a sample filter."
            entry 1
                action forward
                match
                    application eq "mirror"
                    severity eq critical
                exit
            exit
        exit
...
log-id 2
            shutdown
            description "This is a test log file."
            filter 1
            from main security
            to file 1
        exit
...
------------------------------------------
A:ALA-12>config>log#

Configuring an SNMP Trap Group

The associated log-id does not have to configured before a snmp-trap-group can be created, however, the snmp-trap-group must exist before the log-id can be configured to use it.

The following displays a basic SNMP trap group configuration example:

A:ALA-12>config>log# info
----------------------------------------------
...
snmp-trap-group 2
trap-target 10.10.10.104:5 "snmpv3" notify-community "coummunitystring" 
        exit
...
log-id 2
            description "This is a test log file."
            filter 1
            from main security
            to file 1
exit
...
----------------------------------------------
A:ALA-12>config>log#

The following displays a SNMP trap group, log, and interface configuration examples:

A:SetupCLI>config>log# snmp-trap-group 44
A:SetupCLI>config>log>snmp-trap-group# info
----------------------------------------------
      trap-target "xyz-test" address xx.xx.x.x snmpv2c notify-community "xyztesting"
      trap-target "test2" address xx.xx.xx.x snmpv2c notify-community "xyztesting"
----------------------------------------------
*A:SetupCLI>config>log>log-id# info
----------------------------------------------
      from main
      to snmp
----------------------------------------------
*A:SetupCLI>config>router# interface xyz-test
*A:SetupCLI>config>router>if# info
----------------------------------------------
      address xx.xx.xx.x/24
      port 1/1/1
----------------------------------------------
*A:SetupCLI>config>router>if#

Setting the Replay Parameter

For this example the replay parameter was set by a SNMP SET request for the trap-target address 10.10.10.3 which is bound to port-id 1/1/1.

A:SetupCLI>config>log>snmp-trap-group 44
A:SetupCLI>config>log>snmp-trap-group# info
----------------------------------------------
trap-target "xyz-test" address 10.10.10.3 snmpv2c notify-community "xyztesting" replay
trap-target "test2" address 20.20.20.5 snmpv2c notify-community "xyztesting"
----------------------------------------------
A:SetupCLI>config>log>snmp-trap-group#

In the following output, the Replay field changed from disabled to enabled.

A:SetupCLI>config>log>snmp-trap-group# show log snmp-trap-group 44
===============================================================================
SNMP Trap Group 44
===============================================================================
Description : none
-------------------------------------------------------------------------------
Name        : xyz-test
Address     : 10.10.10.3
Port        : 162
Version     : v2c
Community   : xyztesting
Sec. Level  : none
Replay      : enabled
Replay from : n/a
Last replay : never
-------------------------------------------------------------------------------
Name        : test2
Address     : 20.20.20.5
Port        : 162
Version     : v2c
Community   : xyztesting
Sec. Level  : none
Replay      : disabled
Replay from : n/a
Last replay : never
===============================================================================
A:SetupCLI>config>log>snmp-trap-group#

Since no events are waiting to be replayed, the log displays as before.

A:SetupCLI>config>log>snmp-trap-group# show log log-id 44
===============================================================================
Event Log 44
===============================================================================
SNMP Log contents  [size=100   next event=3819  (wrapped)]
 
3818 2008/04/22 23:35:39.89 UTC WARNING: SYSTEM #2009 Base IP
"Status of vRtrIfTable: router Base (index 1) interface xyz-test (index 35) changed 
administrative state: inService, operational state: inService"
 
3817 2008/04/22 23:35:39.89 UTC WARNING: SNMP #2005 Base xyz-test
"Interface xyz-test is operational"
 
3816 2008/04/22 23:35:39.89 UTC WARNING: SNMP #2005 Base 1/1/1
"Interface 1/1/1 is operational"
 
3815 2008/04/22 23:35:39.71 UTC WARNING: SYSTEM #2009 Base CHASSIS
"Status of Mda 1/1 changed administrative state: inService, operational state:
 inService"
 
3814 2008/04/22 23:35:38.88 UTC MINOR: CHASSIS #2002 Base Mda 1/2
"Class MDA Module : inserted"
 
3813 2008/04/22 23:35:38.88 UTC MINOR: CHASSIS #2002 Base Mda 1/1

Shutdown In-Band Port

A shutdown on the in-band port that the trap-target address is bound to causes the route to that particular trap target to be removed from the route table. When the SNMP module is notified of this event, it marks the trap-target as inaccessible and saves the sequence-id of the first SNMP notification that will be missed by the trap-target.

Example: config>log>snmp-trap-group# exit all #configure port 1/1/1 shutdown # # tools perform log test-event #

The Replay from field is updated with the sequence-id of the first event that will be replayed when the trap-target address is added back to the route table.

*A:SetupCLI# show log snmp-trap-group 44
===============================================================================
SNMP Trap Group 44
===============================================================================
Description : none
-------------------------------------------------------------------------------
Name        : xyz-test
Address     : 10.10.10.3
Port        : 162
Version     : v2c
Community   : xyztesting
Sec. Level  : none
Replay      : enabled
Replay from : event #3819
Last replay : never
-------------------------------------------------------------------------------
Name        : test2
Address     : 20.20.20.5
Port        : 162
Version     : v2c
Community   : xyztesting
Sec. Level  : none
Replay      : disabled
Replay from : n/a
Last replay : never
===============================================================================
*A:SetupCLI# 

A display of the event log indicates which trap targets are not accessible and waiting for notification replay and the sequence ID of the first notification that will be replayed.

Note:

If there are more missed events than the log size, the replay will actually start from the first available missed event.

*A:SetupCLI# show log log-id 44
===============================================================================
Event Log 44
===============================================================================
SNMP Log contents  [size=100   next event=3821  (wrapped)]
Cannot send to SNMP target address 10.10.10.3.
Waiting to replay starting from event #3819
 
3820 2008/04/22 23:41:28.00 UTC INDETERMINATE: LOGGER #2011 Base Event Test
"Test event has been generated with system object identifier tmnxModelSR12Reg.
System description: TiMOS-B-0.0.private both/i386 Nokia 7750 SR Copyright (c) 
2000-2016 Nokia. All rights reserved. All use subject to applicable license
agreements. Built on Tue Apr 22 14:41:18 PDT 2008 by test123 in /test123/ws/panos/
main"
 
3819 2008/04/22 23:41:20.37 UTC WARNING: MC_REDUNDANCY #2022 Base operational state
 of peer chan*
"The MC-Ring operational state of peer 2.2.2.2 changed to outOfService."
 
3818 2008/04/22 23:35:39.89 UTC WARNING: SYSTEM #2009 Base IP
"Status of vRtrIfTable: router Base (index 1) interface xyz-test (index 35) changed 
administrative state: inService, operational state: inService"
 
3823 2008/04/22 23:41:49.82 UTC WARNING: SNMP #2005 Base xyz-test
"Interface xyz-test is operational"

No Shutdown Port

A no shutdown command executed on the in-band port to which the trap-target address is bound will cause the route to that trap target to be re-added to the route table. When the SNMP trap module is notified of this event, it resends the notifications that were missed while there was no route to the trap-target address.

Example: configure# port 1/1/1 no shutdown # # tools perform log test-event

After the notifications have been replayed the Replay from field indicates n/a because there are no more notifications waiting to be replayed and the Last replay field timestamp has been updated.

*A:SetupCLI# show log snmp-trap-group 44
===============================================================================
SNMP Trap Group 44
===============================================================================
Description : none
-------------------------------------------------------------------------------
Name        : xyz-test
Address     : 10.10.10.3
Port        : 162
Version     : v2c
Community   : xyztesting
Sec. Level  : none
Replay      : enabled
Replay from : n/a
Last replay : 04/22/2008 18:52:36
-------------------------------------------------------------------------------
Name        : test2
Address     : 20.20.20.5
Port        : 162
Version     : v2c
Community   : xyztesting
Sec. Level  : none
Replay      : disabled
Replay from : n/a
Last replay : never
===============================================================================
*A:SetupCLI# 

A display of the event log shows that it is no longer waiting to replay notifications to one or more of its trap target addresses. An event message has been written to the logger that indicates the replay to the trap-target address has happened and displays the notification sequence ID of the first and last replayed notifications.

*A:SetupCLI# show log log-id 44
===============================================================================
Event Log 44
===============================================================================
SNMP Log contents  [size=100   next event=3827  (wrapped)]
 
3826 2008/04/22 23:42:02.15 UTC MAJOR: LOGGER #2015 Base Log-id 44
"Missed events 3819 to 3825 from Log-id 44 have been resent to SNMP notification
 target address 10.10.10.3."
 
3825 2008/04/22 23:42:02.15 UTC INDETERMINATE: LOGGER #2011 Base Event Test
"Test event has been generated with system object identifier tmnxModelSR12Reg.
System description: TiMOS-B-0.0.private both/i386 Nokia 7750 SR Copyright (c) 
2000-2016 Nokia.
All rights reserved. All use subject to applicable license agreements.
Built on Tue Apr 22 14:41:18 PDT 2008 by test123 in /test123/ws/panos/main"
 
3824 2008/04/22 23:41:49.82 UTC WARNING: SYSTEM #2009 Base IP
"Status of vRtrIfTable: router Base (index 1) interface xyz-test (index 35) changed
 administrative state: inService, operational state: inService"
 
3823 2008/04/22 23:41:49.82 UTC WARNING: SNMP #2005 Base xyz-test
"Interface xyz-test is operational"

Configuring a Syslog Target

Log events cannot be sent to a syslog target host until a valid syslog ID exists.

The following displays a syslog configuration example:

A:ALA-12>config>log# info
----------------------------------------------
...
        syslog 1
            description "This is a syslog file."
            address 10.10.10.104
            facility user
            level warning
        exit
...
----------------------------------------------
A:ALA-12>config>log#

Configuring an Accounting Custom Record

A:ALA-48>config>subscr-mgmt>acct-plcy# info
----------------------------------------------
..
            custom-record
                queue 1
                    i-counters
                        high-octets-discarded-count
                        low-octets-discarded-count
                        in-profile-octets-forwarded-count
                        out-profile-octets-forwarded-count
                    exit
                    e-counters
                        in-profile-octets-forwarded-count
                        in-profile-octets-discarded-count
                        out-profile-octets-forwarded-count
                        out-profile-octets-discarded-count
                    exit
                exit
                significant-change 20
                ref-queue all
                    i-counters
                        in-profile-packets-forwarded-count
                        out-profile-packets-forwarded-count
                    exit
                    e-counters
                        in-profile-packets-forwarded-count
                        out-profile-packets-forwarded-count
                    exit
                exit
..
----------------------------------------------
A:ALA-48>config>subscr-mgmt>acct-plcy#

The following is an example custom record configuration.

Dut-C>config>log>acct-policy>cr# info 
----------------------------------------------
                aa-specific
                    aa-sub-counters
                        short-duration-flow-count
                        medium-duration-flow-count
                        long-duration-flow-count
                        total-flow-duration
                        total-flows-completed-count
                    exit
                    from-aa-sub-counters
                        flows-admitted-count
                        flows-denied-count
                        flows-active-count
                        packets-admitted-count
                        octets-admitted-count
                        packets-denied-count
                        octets-denied-count
                        max-throughput-octet-count
                        max-throughput-packet-count
                        max-throughput-timestamp
                        forwarding-class
                    exit
                    to-aa-sub-counters
                        flows-admitted-count
                        flows-denied-count
                        flows-active-count
                        packets-admitted-count
                        octets-admitted-count
                        packets-denied-count
                        octets-denied-count
                        max-throughput-octet-count
                        max-throughput-packet-count
                        max-throughput-timestamp
                        forwarding-class
                    exit
                exit
                significant-change 1
                ref-aa-specific-counter any
----------------------------------------------

Log Management Tasks

This section discusses the following logging tasks:

  1. Modifying a Log File on page 498
  2. Deleting a Log File on page 499
  3. Modifying a File ID on page 499
  4. Modifying a Syslog ID on page 500
  5. Modifying an SNMP Trap Group on page 501
  6. Deleting an SNMP Trap Group on page 502
  7. Modifying a Log Filter on page 502
  8. Modifying Event Control Parameters on page 503
  9. Returning to the Default Event Control Configuration on page 504

Modifying a Log File

The following displays the current log configuration:

ALA-12>config>log>log-id# info
----------------------------------------------
...
log-id 2
            description "This is a test log file."
            filter 1
            from main security
            to file 1
exit
...
----------------------------------------------
ALA-12>config>log>log-id#

The following displays an example to modify log file parameters:

Example:
Example: config# log config>log# log-id 2 config>log>log-id# description "Chassis log file." config>log>log-id# filter 2 config>log>log-id# from security config>log>log-id# exit

The following displays the modified log file configuration:

A:ALA-12>config>log# info
----------------------------------------------
...
log-id 2
            description "Chassis log file."
            filter 2
            from security
            to file 1
exit
...
----------------------------------------------
A:ALA-12>config>log#

Deleting a Log File

The log ID must be shutdown first before it can be deleted. In a previous example, file 1 is associated with log-id 2.

A:ALA-12>config>log# info
----------------------------------------------
file-id 1
            description "LocationTest."
            location cf1:
            rollover 600 retention 24
        exit
...
log-id 2
            description "Chassis log file."
            filter 2
            from security
            to file 1
exit
...
----------------------------------------------
A:ALA-12>config>log#
 

The following displays an example to delete a log file:

Example:
Example: config# log config>log# log-id 2 config>log>log-id# shutdown config>log>log-id# exit config>log# no log-id 2

Modifying a File ID

The following displays the current log configuration:

A:ALA-12>config>log# info
------------------------------------------
        file-id 1
            description "This is a log file."
            location cf1:
            rollover 600 retention 24
        exit
----------------------------------------------
A:ALA-12>config>log#

The following displays an example to modify log file parameters:

Example:
Example: config# log config>log# file-id 1 config>log>file-id# description "LocationTest." config>log>file-id# rollover 2880 retention 500 config>log>file-id# exit

The following displays the file modifications:

A:ALA-12>config>log# info
----------------------------------------------
...
file-id 1
    description "LocationTest."
    rollover 2880 retention 500
exit
...
----------------------------------------------
A:ALA-12>config>log#

The following displays an example to modify log file parameters:

Example:
Example: config# log config>log# file-id 1 config>log>file-id# description "LocationTest." config>log>file-id# location cf2: config>log>file-id# rollover 2880 retention 500 config>log>file-id# exit

The following displays the file modifications:

A:ALA-12>config>log# info
----------------------------------------------
...
file-id 1
            description "LocationTest."
            location cf2:
            rollover 2880 retention 500
        exit
...
----------------------------------------------
A:ALA-12>config>log#

Modifying a Syslog ID

The following displays an example of the syslog ID modifications:

Example:
Example: config# log config>log# syslog 1 config>log>syslog$ description "Test syslog." config>log>syslog# address 10.10.0.91 config>log>syslog# facility mail config>log>syslog# level info

The following displays the syslog configuration:

A:ALA-12>config>log# info
----------------------------------------------
...
        syslog 1
            description "Test syslog."
            address 10.10.10.91
            facility mail
            level info
        exit
...
----------------------------------------------
A:ALA-12>config>log#

Modifying an SNMP Trap Group

The following displays the current SNMP trap group configuration:

A:ALA-12>config>log# info
----------------------------------------------
...
snmp-trap-group 10
    trap-target 10.10.10.104:5 "snmpv3" notify-community "coummunitystring" 
exit
...
----------------------------------------------
A:ALA-12>config>log#

The following displays an example of the command usage to modify an SNMP trap group:

Example:
Example: config# log config>log# snmp-trap-group 10 config>log>snmp-trap-group# no trap-target 10.10.10.104:5 config>log>snmp-trap-group# snmp-trap-group# trap-target 10.10.0.91:1 snmpv2c notify-community "com1"

The following displays the SNMP trap group configuration:

A:ALA-12>config>log# info
----------------------------------------------
...
        snmp-trap-group 10
            trap-target 10.10.0.91:1 "snmpv2c" notify-community "com1”
        exit
...
----------------------------------------------
A:ALA-12>config>log#

Deleting an SNMP Trap Group

The following displays the SNMP trap group configuration:

A:ALA-12>config>log# info
----------------------------------------------
...
       snmp-trap-group 10
           trap-target 10.10.0.91:1 "snmpv2c" notify-community "com1"
       exit
...
----------------------------------------------
A:ALA-12>config>log#

The following displays an example to delete a trap target and an SNMP trap group.

Example:
Example: config>log# snmp-trap-group 10 config>log>snmp-trap-group# no trap-target 10.10.0.91:1 config>log>snmp-trap-group# exit config>log# no snmp-trap-group 10

Modifying a Log Filter

The following output displays the current log filter configuration:

ALA-12>config>log# info
#------------------------------------------
echo "Log Configuration "
#------------------------------------------
...
        filter 1
            default-action drop
            description "This is a sample filter."
            entry 1
                action forward
                match
                    application eq "mirror"
                    severity eq critical
                exit
            exit
        exit
...
------------------------------------------
ALA-12>config>log#

The following displays an example of the log filter modifications:

Example:
Example: config# log config>log# filter 1 config>log>filter# description "This allows <n>." config>log>filter# default-action forward config>log>filter# entry 1 config>log>filter>entry$ action drop config>log>filter>entry# match config>log>filter>entry>match# application eq user config>log>filter>entry>match# number eq 2001 config>log>filter>entry>match# no severity config>log>filter>entry>match# exit

The following displays the log filter configuration:

A:ALA-12>config>log>filter# info
----------------------------------------
...
        filter 1
            description "This allows <n>."
            entry 1
                action drop
                match
                    application eq "user"
                    number eq 2001
                exit
            exit
        exit
...
----------------------------------------
A:ALA-12>config>log>filter#

Modifying Event Control Parameters

The following displays the current event control configuration:

A:ALA-12>config>log# info
----------------------------------------------
...
event-control "bgp" 2014 generate critical
...
----------------------------------------------
A:ALA-12>config>log#

The following displays an example of an event control modification:

Example:
Example: config# log config>log# event-control bgp 2014 suppress

The following displays the log filter configuration:

A:ALA-12>config>log# info
----------------------------------------------
...
        event-control "bgp" 2014 suppress
...
----------------------------------------------
A:ALA-12>config>log#

The following displays the current event control configuration:

A:ALA-12>config>log# info
----------------------------------------------
...
event-control "ospf" 2014 generate critical
...
----------------------------------------------
A:ALA-12>config>log#

The following displays an example of an event control modification:

Example:
Example: config# log config>log# event-control ospf 2014 suppress

The following displays the log filter configuration:

A:ALA-12>config>log# info
----------------------------------------------
...
        event-control "ospf" 2014 suppress
...
----------------------------------------------
A:ALA-12>config>log#

Returning to the Default Event Control Configuration

The no form of the event-control command returns modified values back to the default values.

Use the following CLI syntax to modify event control parameters:

CLI Syntax:
config>log
no event-control application [event-name |event-nunmber]

The following displays an example of the command usage to return to the default values:

Example:
Example: config# log config>log# no event-control "bgp" 2001 config>log# no event-control "bgp" 2002 config>log# no event-control "bgp" 2014
A:ALA-12>config>log# info detail
----------------------------------------------
#------------------------------------------
echo "Log Configuration"
#------------------------------------------
        event-control "bgp" 2001 generate minor
        event-control "bgp" 2002 generate warning
        event-control "bgp" 2003 generate warning
        event-control "bgp" 2004 generate critical
        event-control "bgp" 2005 generate warning
        event-control "bgp" 2006 generate warning
        event-control "bgp" 2007 generate warning
        event-control "bgp" 2008 generate warning
        event-control "bgp" 2009 generate warning
        event-control "bgp" 2010 generate warning
        event-control "bgp" 2011 generate warning
        event-control "bgp" 2012 generate warning
        event-control "bgp" 2013 generate warning
        event-control "bgp" 2014 generate warning
        event-control "bgp" 2015 generate critical
        event-control "bgp" 2016 generate warning
...
----------------------------------------------
A:ALA-12>config>log#